DSG DCT DPS6 Dual Clutch Transmission Remover Installer Tool Set Kit for Ford US

DSG DCT DPS6 Dual Clutch Transmission Remover Installer Tool Set Kit for Ford US
DSG DCT DPS6 Dual Clutch Transmission Remover Installer Tool Set Kit for Ford US
DSG DCT DPS6 Dual Clutch Transmission Remover Installer Tool Set Kit for Ford US
DSG DCT DPS6 Dual Clutch Transmission Remover Installer Tool Set Kit for Ford US
DSG DCT DPS6 Dual Clutch Transmission Remover Installer Tool Set Kit for Ford US
DSG DCT DPS6 Dual Clutch Transmission Remover Installer Tool Set Kit for Ford US
DSG DCT DPS6 Dual Clutch Transmission Remover Installer Tool Set Kit for Ford US
DSG DCT DPS6 Dual Clutch Transmission Remover Installer Tool Set Kit for Ford US

DSG DCT DPS6 Dual Clutch Transmission Remover Installer Tool Set Kit for Ford US

DSG DCT DPS6 Dual Clutch Transmission Remover Installer Tool Set Kit for Ford US. This Transmission Remover Installer Tool is specially used to remove, install and reinstall the reset DPS6 dry dual clutch transmission. Disassemble the double clutch fixing snap ring, install the three claws and pull out the double clutch.

The transport fastener must be put back in place if the double clutch is used again after disassembly. Resprings/re-trips the springs on the clutch so that you can reinstall it again. Disassemble the double clutch fixing snap ring, install and remove the three claws and pull out the double clutch. Put the double clutch into the base of the tool, insert the cylinder into the base with the inside facing up, and place the two tool wrenches in the appropriate position. Tap the two wrenches to pinch them (the two wrenches are pinched when locked, you can use a hard object to pat them loose). Take out the dual-clutch locking tool? To align the base, screw in the screw and knead the two wrenches, unscrew the bearing nut on the screw, and release the wrench into the three-side clamping slot when it is in position Locking tool? And align it with the appropriate slot to fit it into the base cylinder. Screw in the screw, pinch the two wrenches, and unscrew the bearing nut. When you hear a few crackling sounds, remove the locking tool? And see if the internal card slot enters the round hole.

If not, continue to step 4. At this point, the dual clutch tool has been locked and can be installed at any time. Instructions for installing an unlock lock.

Insert the locked double clutch, put it into the mounting sleeve, install the extension feet on three sides to fix the proper holes, and fix the extension feet. Unscrew the screw and observe whether it is in place. When in place, remove the tool and install the retaining ring.

Remove the motor on both sides, use the hexagonal tool to insert the motor teeth, and rotate it counterclockwise to the end (there is a popping sound when rotating, and the double clutch slightly pops up). Turn the other side counterclockwise again. At this point, the dual clutch has been unlocked and can be loaded. (1)We are a professional worldwide wholesale company, with own factory located in China. We supply many products on Automobile consumer. Also offer reasonable prices, excellent customer service and a reliable credit standing are our target! We are a professional Authorized dealers of AUTOOL, Launch, Autel and Xtool. (3)Global logistics system:US warehouse, German warehouse, China warehouse. (3)Welcome your any-time parchase! This item is in the category "eBay Motors\Automotive Tools & Supplies\Hand Tools\Other Automotive Hand Tools".

The seller is "toolsmakeforlife16" and is located in this country: US. This item can be shipped to United States.


DSG DCT DPS6 Dual Clutch Transmission Remover Installer Tool Set Kit for Ford US


Homepage    Archives    Contact Us    Privacy Policies    Terms of service